New Holland & Case IH Fault Codes List DTC
TYPE CODE ERROR
ENG 111 Engine Controller Failure - Hardware Failure
ENG 115 Engine Speed Sensor (8.3, 9 Liter) or Cam Sensor (15 Liter) is failed
ENG 121 Engine Position Sensor (8.3, 9 Liter) or Crankshaft Sensor (15 Liter) is failed
ENG 122 Boost Pressure Sensor voltage is too high
ENG 123 Boost Pressure Sensor voltage is too low
ENG 124 Boost Pressure level has exceeded the warning limit.
ENG 131 Decelerator or Hand Throttle (STD cab) Position potentiometer voltage is too high
ENG 132 Decelerator or Hand Throttle (STD cab) Position potentiometer voltage is too low
ENG 133 Decelerator (STD cab) Position potentiometer voltage is too high
ENG 134 Decelerator (STD cab) Position potentiometer voltage is too low
ENG 135 Oil Pressure Sensor voltage is too high
ENG 141 Oil Pressure Sensor voltage is too low
ENG 143 Oil Pressure level has fallen below the warning limit.
ENG 144 Coolant Temperature Sensor voltage is too high
ENG 145 Coolant Temperature Sensor voltage is too low
ENG 146 Coolant Temperature level has exceeded the warning limit.
ENG 147 Frequency Throttle Signal shorted high
ENG 148 Frequency Throttle Signal shorted low
ENG 151 Coolant Temperature level has exceeded the warning limit.
ENG 153 Intake Manifold Temperature Sensor voltage is too high
ENG 154 Intake Manifold Temperature Sensor voltage is too low
ENG 155 Intake Manifold Temperature level has exceeded the warning limit.
ENG 187 Sensor Supply 2 Voltage is too low.
ENG 191 A/C clutch driver shorted to ground when ON.
ENG 211 Communications problem with Armrest, Instrumentation, or Transmission Controllers
ENG 212 Oil Temperature Sensor Voltage is too high
ENG 213 Oil Temperature Sensor Voltage is too low
ENG 214 Oil Temperature Sensor Voltage is above normal range
ENG 219 Oil Level - remote reservoir is too low. Add oil.
ENG 221 Ambient Air Pressure Sensor Voltage is too high
ENG 222 Ambient Air Pressure Sensor Voltage is too low
ENG 223 CORS - Burn Valve Solenoid is shorted either low or high
ENG 227 Sensor Supply 2 Voltage is too high.
ENG 234 Engine Speed has exceed the overspeed warning limit.
ENG 235 Engine Coolant Level is low. Add coolant fluid.
ENG 237 External Speed Multi Unit Sync Command Input Data Incorrect.
ENG 241 Vehicle Speed Signal lost
ENG 242 Vehicle Speed Signal intermittent / tampering
ENG 243 Error detected in exhaust brake relay
ENG 245 Fan Clutch Voltage too low
ENG 254 Fuel Shutoff Valve Voltage too low
ENG 255 Fuel Shutoff Valve Voltage too high
ENG 259 Fuel Shutoff Valve mechanically stuck open.
ENG 263 Fuel Temperature Sensor voltage is too high
ENG 265 Fuel Temperature Sensor voltage is too low
ENG 268 Fuel Pressure in pump is not changing with operating conditions.
ENG 271 Front Pumping Control Valve current is low during ñclick testî
ENG 272 Front Pumping Control Valve current is high
ENG 273 Rear Pumping Control Valve current is low during ñclick testî
ENG 274 Rear Pumping Control Valve current is high
ENG 275 Front Pumping element is failed
ENG 276 Injection Control Valve current is out of range
ENG 277 Injection Control Valve is failed
ENG 278 Fuel Lift Pump is failed
ENG 279 Injection Control Valve current is out of range
ENG 281 Front Pumping element is failed
ENG 282 Rear Pumping element is failed
ENG 283 Engine Speed/Position Sensor supply voltage is too high
ENG 284 Engine Speed/Position Sensor supply voltage is too low
ENG 285 J1939 Parameter was set to be multiplexed, but not received (timeout error)
ENG 286 J1939 Parameter was set to be multiplexed, but not available from all sources (config error)
ENG 287 Multiplexing throttle parameter and a data error was received - data invalid
ENG 288 Multiplexing remote throttle parameter and a data error was received - data invalid
ENG 293 Hydraulic Fan Hydraulic Oil Temperature Sensor Voltage is too high
ENG 294 Hydraulic Fan Hydraulic Oil Temperature Sensor Voltage is too low
ENG 295 Ambient Air Pressure data invalid
ENG 297 OEM Pressure Sensor Voltage is too high.
ENG 298 OEM Pressure Sensor Voltage is too low.
ENG 299 Engine Shutdown by other than keyswitch (i.e. via data bus command)
ENG 319 Real Time Clock in controller has lost power
ENG 328 Rear Pumping element is failed
ENG 329 CAPS Pump has an overpumping failure
ENG 338 Idle Shutdown Vehicle Accessory Relay Voltage is too high
ENG 339 Idle Shutdown Vehicle Accessory Relay Voltage is too low
ENG 341 All data written during powerdown cycle was lost (checksum error)
ENG 343 Engine Controller Failure - Hardware Failure
ENG 349 Measured Speed is too high.
ENG 352 5 Volt Sensor Supply voltage is too low
ENG 378 Front Fueling current is too low
ENG 379 Front fueling current is too high
ENG 381 Error detected in cold start relay 1
ENG 382 Error detected in cold start relay 2
ENG 385 5 Volt Sensor Supply voltage is too high
ENG 386 5 Volt Sensor Supply voltage is too high
ENG 387 Decelerator or Hand Throttle (STD cab) 5 Volt Supply voltage is too high
ENG 388 Engine Brake driver 1 circuit failure
ENG 392 Engine Brake driver 2 circuit failure
ENG 393 Engine Brake driver 3 circuit failure
ENG 394 Front Timing current is too low.
ENG 395 Front Timing current is too high.
ENG 396 Rear Fueling current is too low
ENG 397 Rear Fueling current is too high
ENG 398 Rear Timing current is too low
ENG 399 Rear Timing current is too high
ENG 412 J1708 data link cannot transmit
ENG 414 J1708 data link not fast enough
ENG 415 Oil Pressure level has fallen below the very low warning limit.
ENG 418 Water in Fuel sensor indicates the water in the fuel filter needs to be drained.
ENG 419 Boost Pressure data invalid
ENG 422 Engine Coolant Level Sensor (optional) is failed or the jumper plug is missing
ENG 426 J1939 data link cannot transmit
ENG 427 J1939 data link not fast enough
ENG 428 Water in Fuel Sensor voltage is too high.
ENG 429 Water in Fuel Sensor voltage is too low.
ENG 431 Hand Throttle (STD cab) Idle Validation Switches are both closed
ENG 432 Hand Throttle (STD cab) position potentiometer and switches disagree.
ENG 433 Boost Pressure level disagrees with engine operation conditions (speed & power)
ENG 434 Unswitched 12 volt supply voltage disconnected without normal key off sequence.
ENG 435 Oil Pressure data invalid
ENG 441 Battery Voltage is too Low (less than 6 volts)
ENG 442 Battery Voltage is too High
ENG 443 Decelerator or Hand Throttle (STD cab) 5 Volt Supply voltage is too low
ENG 444 Low voltage detected at OEM 5 volt supply
ENG 449 Fuel Pressure level has exceeded the warning limit.
ENG 451 Fuel Pressure Sensor voltage is too high
ENG 452 Fuel Pressure Sensor voltage is too low
ENG 456 Fuel Pressure in pump is not changing with operating conditions.
ENG 465 Wastegate 1 voltage is too high
ENG 466 Wastegate 1 voltage is too low
ENG 482 Fuel Pressure Sensor voltage low
ENG 483 Rear Bank Post Actuactor Pressure voltage high
ENG 484 Rear Bank Post Actuactor Pressure voltage low
ENG 485 Rear Fueling actuator overfueling
ENG 486 Rear Fueling actuator underfueling
ENG 488 Intake Manifold Temperature level has exceeded the warning limit.
ENG 489 Measured Speed Sensor data low
ENG 491 Wastegate 2 voltage is too high
ENG 492 Wastegate 2 voltage is too low
ENG 493 The Injection Control Identifier Circuit in the harness has failed.
ENG 496 Engine Speed / Position Sensor #2 supply is too low
ENG 524 Error detected on high speed governor droop selection switch
ENG 527 Cab pressurization/Ether relay coil circuit shorted high or open
ENG 529 Output B driver shorted high or open
ENG 539 The Injection Control Valve Transorb in the harness has failed. (open circuit)
ENG 546 Fuel Pressure sensor voltage is too high.
ENG 547 Fuel Pressure sensor voltage is too low.
ENG 551 Hand Throttle (STD cab) Idle Validation Switches are both open
ENG 553 Front fueling actuator overfueling
ENG 559 Front fueling actuator underfueling
ENG 581 Fuel inlet Pressure Sensor voltage is too high.
ENG 582 Fuel inlet Pressure Sensor voltage is too low.
ENG 583 Fuel Inlet Pressure Sensor voltageout of range high or low.
ENG 595 Turbo overspeed protection fault
ENG 596 Battery voltage is too high
ENG 597 Battery voltage is too low
ENG 598 Battery voltage is very low
ENG 599 Engine is being shutdown based on OEM input
ENG 611 ECM detected engine initiated protection shutdown or keyed-off while above specific load limit
ENG 697 Engine Controller internal temperature too high
ENG 698 Engine Controller internal temperature too low
ENG 731 Engine Speed / Position #2 - Mechanical misalignment.
ENG 753 Synchronization has been lost.
ENG 755 Front Bank injector is bad.
ENG 758 Rear Bank injector is bad
ENG 951 A power imbalance between the cylinders was detected by the controller hardware
ENG 983 Unused A/D input channel out of range.
ENG 1117 Battery voltage too low, or the controller was not allowed to power down correctly
ENG 1256 Control Module Identification Input State Error.
ENG 1257 Control Module Identification Input State Error.
ENG 2117 Engine Coolant Level is low. Add coolant fluid.
ENG 2186 Supply Voltage to the accelerator pedal position sensor too low.
ENG 2195 Auxiliary Equipment Sensor Input # 3 - Engine Protection Critical - Special Instructions.
ENG 2249 Injector Metering Rail 1 Fuel Pressure lower than commanded pressure.
ENG 2265 Electric Lift Pump for Engine Fuel Supply Voltage too high.
ENG 2266 Electric Lift Pump for Engine Fuel Supply Voltage too low.
ENG 2292 Fuel Inlet Meter Device higher than expected.
ENG 2293 Fuel Inlet Meter Device flow demand lower than expected.
ENG 2311 Electronic Fuel Injection Control Valve open or closed Circuit.
ENG 2321 Engine Crankshaft Speed / Position data invalid.
ENG 2322 Engine Camshaft Speed / Position Sensor data invalid.
ENG 2372 Engine Fuel Filter clogged error
ENG 2555 Intake Air Heater 1 Circuit Voltage too high.
ENG 2558 Auxiliary PWM Driver 1 Circuit Voltage too low.
ENG 2973 Intake Manifold 1 Pressure data invalid.
TRANS 11 Master Clutch Potentiometer Open Circuit or short to ground
TRANS 12 Master Clutch Potentiometer Short to +12 Volts or short to 5 Vreff
TRANS 24 None of the transmission clutches are calibrated
TRANS 37 BOC switch open circuit or Neutral relay stuck open
TRANS 38 Shuttled to reverse when no wheel speed signal was available
TRANS 47 Clutch pedal bottom of clutch switch misadjusted
TRANS 48 BOC switch or Neutral relay short circuit
TRANS 49 Auto Guidance Isolation valve driver Fault
TRANS 50 Park Brake is powered off when in park
TRANS 51 FNRP pod indicates Forward or Reverse is on, when Park is on
TRANS 52 Park Brake is stuck on when commanded off
TRANS 53 5 volt reference voltage too high
TRANS 54 5 volt reference voltage too low
TRANS 59 FNRP pod in illogical state (two positions on at same time)
TRANS 60 FNRP pod in illogical state (in no position)
TRANS 61 System pressure valve solenoid circuit is open circuit or shorted to ground
TRANS 62 System pressure solenoid is shorted to B+
TRANS 64 Transmission output Sped is too high (above 8200 RPM)
TRANS 65 Operator attempted a shuttle operation while out of the seat
TRANS 66 FNRP Pod Forward switch is shorted to ground or open circuit
TRANS 67 FNRP Pod Forward switch is shorted to power
TRANS 68 FNRP Pod Reverse switch is shorted to ground or open circuit
TRANS 69 FNRP Pod Reverse switch is shorted to power
TRANS 70 Battery voltage is too low for clutch solenoid operation
TRANS 72 Transmission Oil Temperature is above 122 deg. C
TRANS 73 Software is out of the calibration mode and the park brake request is still active.
TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration.
TRANS 75 Engine speed from Inst Controller does not match the speed signal from the alternator.
TRANS 76 Engine speed from Eninge Controller does not match the speed signal from the alternator.
TRANS 77 No signal from wheel speed sensor
TRANS 78 Transmission regulated pressure accumulator is discharged
TRANS 79 Engine RPM from the alternator is measured too high
TRANS 80 Wheel speed sensor is measured too high
TRANS 81 Transmission clutches are slipping
TRANS 82 Creep Clutch is not calibrated
TRANS 83 Communications Lost with Engine Controller
TRANS 103 Odd clutch solenoid or its wiring failed open or shorted to ground
TRANS 104 Even clutch solenoid or its wiring failed open or shorted to ground
TRANS 105 C1-2 clutch solenoid or its wiring failed open or shorted to ground
TRANS 106 C3-4 clutch solenoid or its wiring failed open or shorted to ground
TRANS 107 C5-6 clutch solenoid or its wiring failed open or shorted to ground
TRANS 108 Master clutch solenoid or its wiring failed open or shorted to ground
TRANS 109 Low range clutch solenoid or its wiring failed open or shorted to ground
TRANS 110 Mid range clutch solenoid or its wiring failed open or shorted to ground
TRANS 111 High range clutch solenoid or its wiring failed open or shorted to ground
TRANS 112 Reverse clutch solenoid or its wiring failed open or shorted to ground
TRANS 113 Creeper clutch solenoid or its wiring failed open or shorted to ground
TRANS 114 Even clutch solenoid coil or its wiring shorted to power
TRANS 115 Odd clutch solenoid coil or its wiring shorted to power
TRANS 116 C1-2 clutch solenoid coil or its wiring shorted to power
TRANS 117 C3-4 clutch solenoid coil or its wiring shorted to power
TRANS 118 C5-6 clutch solenoid coil or its wiring shorted to power
TRANS 119 Master clutch solenoid coil or its wiring shorted to power
TRANS 120 Low range clutch solenoid coil or its wiring shorted to power
TRANS 121 Mid range clutch solenoid coil or its wiring shorted to power
TRANS 122 High range clutch solenoid coil or its wiring shorted to power
TRANS 123 Reverse clutch solenoid coil or its wiring shorted to power
TRANS 124 Creeper clutch solenoid coil or its wiring shorted to power
TRANS 125 Odd clutch is not calibrated
TRANS 126 Even clutch is not calibrated
TRANS 127 C1-2 clutch is not calibrated
TRANS 128 C3-4 clutch is not calibrated
TRANS 129 C5-6 clutch is not calibrated
TRANS 130 Low range clutch is not calibrated
TRANS 131 Mid range clutch is not calibrated
TRANS 132 High range clutch is not calibrated
TRANS 133 Reverse clutch is not calibrated
TRANS 134 Master clutch is not calibrated
TRANS 135 Communication lost with the armrest controller
TRANS 136 Communication lost with the instrumentation controller
TRANS 137 Front Suspension raise lock solenoid circuit shorted or open circuit
TRANS 138 Front Suspension raise solenoid circuit shorted or open circuit
TRANS 139 Front Suspension lower lock solenoid circuit shorted or open circuit
TRANS 140 Front suspension position is above the expected absolute limit
TRANS 141 Front suspension position is below the expected absolute limit
TRANS 142 Front suspension travel range has not been calibrated
TRANS 143 Front suspension position is above the upper suspension range
TRANS 144 Front suspension position is below the lower suspension range
TRANS 145 Front Suspension lower lock solenoid circuit shorted or open circuit
TRANS 146 Regulated system pressure low (below 100PSI / 689 KPA)
TRANS 147 Regulated system pressure below 290 PSI
TRANS 148 Backup alarm circuit shorted or open
TRANS 150 Front suspension pressure sensor rod side (DA-R) out of range high
TRANS 151 Front suspension pressure sensor rod side open circuit
TRANS 152 Front Suspension pressure control not able to increase pressure on the rod side
TRANS 153 Front Suspension pressure control not able to decrease pressure on the rod side
TRANS 154 Front Suspension Lock Valve Stuck on fault (suspension will not lock)
TRANS 155 Front Suspension Lock Valve is stuck of (suspension will not unlock)
TRANS 156 Lock valve was installed but removed
ARM 19 Hand THROTTLE potentiometer is failed
ARM 29 Aux 1st remote valve LEVER potentiometer is failed
ARM 39 Aux 2nd remote valve LEVER potentiometer is failed
ARM 49 Aux 3rd remote valve LEVER potentiometer is failed
ARM 59 Aux 4th remote valve LEVER potentiometer is failed
ARM 69 HITCH POSITION command potentiometer is failed
ARM 79 HITCH LOAD command potentiometer is failed
ARM 89 Aux 1st remote valve FLOW potentiometer is failed
ARM 99 Aux 2nd remote valve FLOW potentiometer is failed
ARM 109 Aux 3rd remote valve FLOW potentiometer is failed
ARM 119 Aux 4th remote valve FLOW potentiometer is failed
ARM 129 Aux 5th remote valve FLOW potentiometer is failed
ARM 139 Aux remote valve TIMER potentiometer is failed
ARM 149 Hitch UPPER LIMIT potentiometer is failed
ARM 159 Hitch DROP RATE potentiometer is failed
ARM 169 Hitch TRAVEL potentiometer is failed
ARM 1029 Aux 5th remote valve control switch is failed
ARM 1039 PTO switch is failed
ARM 1049 Hitch UP/DOWN switch is failed
ARM 1059 Hitch SLIP switch is failed
ARM 1069 MFD switch is failed
ARM 1079 DIFF LOCK switch is failed
ARM 1089 Programmable UP/DOWN switch is failed.
ARM 1099 Aux remote valve LIMIT SET switch is failed
ARM 1109 Hand Throttle IDLE VALIDATION switch is failed
ARM 1119 RECORD/PLAY switch is failed
ARM 1129 Invalid Configuration - Implement Depth Control switch is failed
ARM 1139 Engine Brake switch is failed
ARM 1149 Auto Field / Transport Switch is in an illogical state
ARM 8011 Battery Voltage is too Low
ARM 9011 Controller Memory Error - Loss of Hitch Position Command Calibration
ARM 9012 Controller Memory Error - Loss of Aux Remote Lever Calibrations
ARM 9013 Controller Memory Error - Loss of Throttle Calibrations
ARM 9014 Controller Memory Error - Loss of MFD switch Configuration
ARM 9015 Controller Memory Error - Loss of Trans switches Configuration
ARM 9021 Hitch position command potentiometer calibration results not acceptable
ARM 9031 Hand throttle potentiometer calibration results not acceptable
ARM 9041 Hitch DROP RATE potentiometer calibration value(s) are out of range
ARM 10091 Armrest Controller failure - 5 V regulator failure
ARM 12013 Communications Lost with Data Bus and ALL other controllers
ARM 12081 Loss of/unavailable Performance Monitor Display - RECORD/PLAY functionality disabled
TMF 3 Hitch Raise Solenoid High Side Driver shorted to 12 volts.
TMF 4 Hitch Raise Solenoid Failed Open or Shorted to Ground.
TMF 5 Hitch Lower Solenoid Shorted to 12 volts.
TMF 6 Hitch Lower Solenoid High Side Driver circuit short to 12 volts.
TMF 7 Hitch Raise/Lower Solenoids Open or short to ground.
TMF 11 Communications Lost with Data Bus and ALL other controllers
TMF 12 Communication lost with the armrest controller
TMF 14 5 Volt Sensor Supply voltage is too high
TMF 15 5 Volt Sensor Supply voltage is too low
TMF 17 Hitch Position Command potentiometer failed in the Armrest controller
TMF 18 Hitch Rockshaft Position potentiometer is outside normal operating range.
TMF 19 Hitch Upper Limit potentiometer is failed in the Armrest Controller
TMF 21 Hitch Load Command potentiometer is failed in the Armrest Controller
TMF 22 Single draft pin sensor failed when configured for one draft pin sensor.
TMF 23 Two draft pin sensors failed when configured for two draft pins.
TMF 24 Communications Lost with Instrumentation Controller
TMF 25 Hitch Up/Down Switch failed in the Armrest controller
TMF 26 Fender UP and DOWN switch failure or both switches simultaneously pressed
TMF 28 Hitch Travel potentiometer is failed in the Armrest Controller
TMF 29 Hitch Drop Rate potentiometer is failed in the Armrest Controller
TMF 30 Right Draft Pin voltage is outside the normal operating range.
TMF 31 Left Draft Pin voltage is outside the normal operating range.
TMF 32 Ground Speed Signal is failed in the Instrumentation Controller
TMF 33 Hitch Slip Set Switch failed in the Armrest controller
TMF 34 Hitch Slip Select Switch failed in the Armrest controller
TMF 35 Slip Sensor (radar or wheel speed) is failed in the Instrumentation Controller
TMF 37 The ARU reports EDC Transport Lock is faulty or not available.
TMF 41 Draft pin(s) detected but the Armrest controller specified tractor without draft control.
TMF 42 Engine speed must be set above 1600 rpm during calibration of lower valve.
TMF 43 No Draft pin(s) detected but the Armrest controller specified tractor with draft control.
TMF 44 Hitch calibration aborted due to tractor movement.
TMF 45 Hitch calibration attempted when the engine is not running or engine speed signal is failed.
TMF 47 Raise Valve calibration value is too high. (valve problem)
TMF 48 Raise Valve calibration value is too low. (valve problem)
TMF 50 Hitch position at top of travel is not within specification during calibration
TMF 51 Lower Valve calibration value is too high. (valve problem)
TMF 52 Lower Valve calibration value is too low. (valve problem)
TMF 53 The time allowed for hitch calibration has expired
TMF 54 Hitch position at bottom of travel is not within specification during calibration
TMF 55 Hitch position range from top to bottom is not within spec during calibration
TMF 56 Hitch position range to position command range ratio is not within spec during calibration.
TMF 57 Right Draft Pin voltage is not within spec for ïno loadà condition during calibration
TMF 58 Left Draft Pin voltage is not within spec for ïno loadà condition during calibration
TMF 59 Both Draft Pin voltages are not within spec for ïno loadà condition during calibration
TMF 60 Draft pin connected to left vs right for single pin setup during calibration
TMF 61 The Hitch Calibration procedure must be performed.
TMF 62 Communications Lost with Performance Monitor Function
TMF 63 Controller 8 volt reference is too high (above 8.8 volts).
TMF 64 Controller 8 volt reference is too low (below 7.2 volts).
TMF 65 Battery Voltage is too Low
TMF 66 Battery Voltage is too Low
TMF 80 MFD fault condition in software.
TMF 81 MFD Solenoid is failed Open or Short Circuit
TMF 82 Differential Lock Solenoid is failed Open or Short Circuit
TMF 83 Brake Lamp Relay Solenoid is failed Open or Short Circuit
TMF 86 Wheel Slip Signal is failed in the Instrumentation Controller
TMF 87 Ground Speed Signal is failed in the Instrumentation Controller
TMF 88 Differential Lock Switch is failed in the Armrest Controller
TMF 89 Differential Lock Switch is failed in the Armrest Controller
TMF 90 Differential Lock Switch is failed in the Armrest Controller
TMF 92 MFD Switch is failed in the Armrest Controller
TMF 93 MFD Switch is failed in the Armrest Controller
TMF 94 Differential Lockout fault condition in software.
TMF 95 The steering angle sensor is above the expected operating range
TMF 96 The steering angle sensor is below the expected operating range
TMF 98 Battery Voltage is too Low
TMF 99 Battery Voltage is too Low
TMF 106 Aux 5th remote valve control switch (Extend) is failed in the Armrest Controller
TMF 107 Aux 5th remote valve control switch (Retract) is failed in the Armrest Controller
TMF 108 Aux 1st remote valve LEVER potentiometer is failed in the Armrest Controller
TMF 109 Aux 2nd remote valve LEVER potentiometer is failed in the Armrest Controller
TMF 110 Aux 3rd remote valve LEVER potentiometer is failed in the Armrest Controller
TMF 111 Aux 4th remote valve LEVER potentiometer is failed in the Armrest Controller
TMF 112 Aux 1st remote valve FLOW potentiometer is failed in the Armrest Controller
TMF 113 Aux 2nd remote valve FLOW potentiometer is failed in the Armrest Controller
TMF 114 Aux 3rd remote valve FLOW potentiometer is failed in the Armrest Controller
TMF 115 Aux 4th remote valve FLOW potentiometer is failed in the Armrest Controller
TMF 116 Aux 5th remote valve FLOW potentiometer is failed in the Armrest Controller
TMF 120 Electro Hydraulic Remote top link switch is stuck on.
TMF 123 Aux 1st Lower Coil solenoid shorted to 12 volts.
TMF 124 Aux 1st Lower solenoid failed open or short circuit.
TMF 125 Aux 1st Raise Coil solenoid shorted to 12 volts.
TMF 126 Aux 1st Raise solenoid failed open or short circuit.
TMF 127 Aux 2nd Lower Coil solenoid shorted to 12 volts.
TMF 128 Aux 2nd Lower solenoid failed open or short circuit.
TMF 129 Aux 2nd Raise Coil solenoid shorted to 12 volts.
TMF 130 Aux 2nd Raise solenoid failed open or short circuit.
TMF 131 Aux 3rd Lower Coil solenoid shorted to 12 volts.
TMF 132 Aux 3rd Lower solenoid failed open or short circuit.
TMF 133 Aux 3rd Raise Coil solenoid shorted to 12 volts.
TMF 134 Aux 3rd Raise solenoid failed open or short circuit.
TMF 135 Aux 4th Lower Coil solenoid shorted to 12 volts.
TMF 136 Aux 4th Lower solenoid failed open or short circuit.
TMF 137 Aux 4th Raise Coil solenoid shorted to 12 volts.
TMF 138 Aux 4th Raise solenoid failed open or short circuit.
TMF 139 Aux 5th Lower Coil solenoid shorted to 12 volts.
TMF 141 Aux 5th Raise Coil solenoid shorted to 12 volts.
TMF 142 Aux 5th Raise solenoid failed open or short circuit.
TMF 147 Implement feedback #1 out of range High
TMF 148 Implement feedback #1 out of range Low
TMF 149 Implement feedback #2 out of range High
TMF 150 Implement feedback #2 out of range Low
TMF 151 Communications Lost with Transmission Controller
TMF 152 Electro Hydraulic Remote top link switch voltage is short circuit.
TMF 153 Electro Hydraulic Remote top link switch data invalid
TMF 154 PTO switch interlock - Cab Switch and Fender switch on at the same time.
TMF 155 Auto PTO switch data failed in the Armrest controller.
TMF 156 Auto PTO switch stuck ON in Armrest Controller.
TMF 157 PTO remote fender switch short circuit.
TMF 158 PTO remote fender switch open circuit
TMF 159 PTO remote fender switch stuck ON.
TMF 160 PTO Clutch is Slipping Too Much
TMF 162 Engine Stalled when the PTO was running.
TMF 163 PTO Shaft rotation is detected when the PTO clutch is OFF.
TMF 164 PTO shaft speed has not been detected within 3.6 seconds of being turned ON.
TMF 165 PTO Shaft rotation is detected when the Engine is OFF.
TMF 166 PTO Driver is on and no current is sensed.
TMF 167 Current sensed when the PTO driver is off.
TMF 168 PTO ON/OFF switch is failed in the Armrest Controller
TMF 169 PTO ON/OFF switch is failed in the Armrest Controller
TMF 170 PTO ON/OFF switch is failed in the Armrest Controller
TMF 171 PTO software fault condition detected.
TMF 172 PTO Solenoid Circuit is failed shorted to 12 Volts when PTO is in the off state.
TMF 173 PTO Solenoid Circuit is failed shorted to ground when PTO is in the off state.
TMF 174 Current flowing in the PTO sense resistor when the high side is off.
TMF 175 PTO Clutch has not reached lock up speed within 6 seconds of being turned ON
TMF 178 PTO speed sensor has been changed.
TMF 179 The PTO is receiving no frequency from the Shaft Size Sensor on a two speed PTO
TMF 180 The PTO is receiving signals from the Shaft Size Sensor on a single speed PTO configuration.
INST 1015 Seat Switch may be stuck closed.
INST 1024 Trans oil filter switch shorted to ground on power up.
INST 1034 Hydraulic oil filter switch shorted to ground on power up.
INST 3010 PTO Shaft Speed sensor is failed in PTO Controller
INST 3020 Engine Speed sensor is failed in the Engine Controller
INST 3022 Engine Overspeed Error
INST 5010 Engine Oil Pressure sensor is failed in the Engine Controller
INST 5011 Engine Oil Pressure sensor voltage is too low (open circuit, short to ground)
INST 7024 Reversible Fan Control open circuit or shorted to ground.
INST 10031 Controller Memory Error - Loss of Engine Hours information
INST 10032 Controller Memory Error - Loss of Vehicle Configuration information
INST 10033 Controller Memory Error - Loss of Customer Configuration information
INST 10034 Controller Memory Error: Loss of valid fuel table information.
INST 10035 Controller Memory Error - Loss of Valid Radar Configuration information.
INST 10036 Controller Memory Error - Loss of Displayed Performance information
INST 10037 Controller Memory Error - Loss of Implement Width information
INST 10038 Controller Memory Error - Loss of Valid Remote Timer information.
INST 11011 Fuel Level Sensor voltage is too low (open circuit, short to ground)
INST 12011 Communications Lost with Armrest Controller
INST 12021 Communications Lost with Auxiliary Controller
INST 12031 Communications Lost with Hitch Controller
INST 12043 Communications Lost with Data Bus 1 and ALL other controllers
INST 12051 Communications Lost with PTO Controller
INST 12053 Communications Lost with Vehicle Data Bus 2.
INST 12071 Communications Lost with Transmission Controller
INST 12091 Communications Lost with Engine Controller
INST 12101 Communications Lost with Tractor ECU (Gateway) Controller
INST 12111 Communications Lost with Automatic Temperature Controller
INST 12121 Communications Lost with Color Perfomance Monitor
INST 13010 Engine Coolant Temperature sensor is failed in the Engine Controller
INST 13011 Engine Coolant Temperature sensor voltage is too low (short to ground)
INST 13012 Engine Coolant Temperature sensor voltage is too high (open circuit, short to +V)
INST 13021 Transmission Oil Temperature sensor voltage is too low (short to ground)
INST 13022 Transmission Oil Temperature sensor voltage is too high (open circuit, short to +V)
INST 13031 Hydraulic Oil Temperature sensor voltage is too low (short to ground)
INST 13032 Hydraulic Oil Temperature sensor voltage is too high (open circuit, short to +V)
INST 13040 Air to Air Intake Temperature sensor is failed in the Engine Controller
INST 13044 When fuel shut off relay is latched, short is detected (mechanical engine tractors only)
INST 13051 Air to Air Intake Temperature sensor voltage is too low (short to ground)
INST 13052 Air to Air Intake Temperature sensor voltage is too high (open circuit, short to +V)
INST 53001 Instrumentation Controller Configuration is Incorrect
INST 53002 Air to Air Intake sensor does not match Tractor Model Configuration
INST 53005 Engine Shutdown activated by Instrument Controller
INST 65535 NO ERROR. Errors have not been cleared from factory.
ATC 111 Cab sensor open or shorted to power
ATC 112 Cab sensor shorted to ground
ATC 115 Evaporator sensor open or shorted to power
ATC 116 Evaporator sensor shorted to ground
ATC 120 Blower speed select pot open/shorted to power
ATC 121 Temperature select pot open/shorted to power
ATC 122 Mode Select Pot Open Or Shorted To Power
ATC 125 High pressure switch (+) input shorted to power
ATC 126 High pressure switch (+) input shorted to ground
ATC 127 High pressure switch (-) input shorted to power
ATC 128 High pressure switch (-) input shorted to ground
ATC 129 High pressure cycling error (2 in 1 minute)
ATC 130 Low pressure switch (+) input shorted to power
ATC 131 Low pressure switch (+) input shorted to ground
ATC 132 Low pressure switch (-) input shorted to power
ATC 133 Low pressure switch (-) input shorted to ground
ATC 134 Low pressure switch open for > 1 minute
ATC 113 Outlet sensor open or shorted to power
ATC 114 Outlet sensor shorted to ground
ATC 117 Outside air sensor open or shorted to power
ATC 118 Outside air sensor shorted to ground
Trans 2009 Seat switch open circuit
Trans 2010 Seat switch is shorted to the supply voltage B+ or 5 volt reference
Trans 2011 Clutch Pot Open Circuit or short to ground
Trans 2012 Clutch Potentiometer Short to +12 Volts or short to 5 Volt reference.
Trans 2024 none of the Transmission clutches are calibrated. This will be the condition when a new controller is installed on the tractor.
Trans 2037 Bottom of Clutch pedal switch open circuit or bottom of clutch relay is stuck open
Trans 2047 Clutch pedal bottom of clutch switch misadjusted.
Trans 2048 Bottom of Clutch pedal switch or the bottom of clutch relay are short circuit
Trans 2049 Trans
Trans 2054 5 volt reference voltage too low.
Trans 2055 No signal from wheel speed sensor.
Trans 2056 5 volt internal reference voltage too high.
Trans 2057 5 volt internal reference voltage too low.
Trans 2059 1) Switch inputs indicate shuttle lever is in both forward and neutral 2) Switch inputs indicate shuttle lever is in both reverse and neutral3) Switch inputs indicate shuttle lever is in both forward and reverse. Cycle the shuttle lever which may free up stuck switches, or try driving the opposite direction.
Trans 2071 Forward switch input from the FNRP Pod is shorted to ground or is open circuit.
Trans 2072 Reverse switch input from the FNRP Pod is shorted to +12 Volts or the FNRP pod 5 Volt Reference.
Trans 2073 Reverse switch input from the FNRP Pod is shorted to ground or open circuit.
Trans 2074 FNR Not Park Switch low voltage fault
Trans 2075 FNR Not Park Switch high Voltage fault
Trans 2110 FNR Neutral Switch Low Voltage fault
Trans 2111 FNR Neutral Switch high Voltage fault
Trans 2326 The Engine RPM sourced from the alternator measured by the controller is excessively high.
Trans 2327 No engine RPM
Trans 2330 The Transmission output RPM speed, sourced from the sensor, measured by the controller is too high for the desired gear
Trans 2331 The transmission clutches are slipping
Trans 2342 Clutch Odd solenoid open circuit or short to ground.
Trans 2343 Clutch Even solenoid open circuit or short to ground.C33
Trans 2344 Clutch C1-2 solenoid open circuit or short to ground.
Trans 2345 Clutch C3-4 solenoid open circuit or short to ground.
Trans 2346 Clutch 5-6 solenoid open circuit or short to ground.
Trans 2374 Master Clutch solenoid open circuit or short to ground.
Trans 2347 Clutch Low Range solenoid open circuit or short to ground.
Trans 2348 110 Clutch Mid Range solenoid open circuit or short to ground.
Trans 2349 Clutch High Range solenoid open circuit or short to ground.
Trans 2350 Clutch reverse solenoid open circuit or short to ground.
Trans 2351 The creeper clutch solenoid is open circuit or short to ground
Trans 2353 Even Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.
Trans 2352 Odd Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.
Trans 2354 C1-2 Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off..
Trans 2355 C3-4 Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off.
Trans 2356 C5-6 clutch Solenoid is shorted to +12 Volts, current sensed while driver isoff.
Trans 2357 Low clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.
Trans 2358 Mid Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off.
Trans 2359 High Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.
Trans 2360 Reverse Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.
Trans 2361 The creeper clutch solenoid is shorted to +12 Volts, current sensed while the driver is off
Trans 2362 Master Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off.
Trans 2363 The Odd Clutch is not calibrated
Trans 2364 Even Clutch not calibrated
Trans 2365 C1-2 Clutch not calibrated
Trans 2366 C3-4 Clutch not calibrated
Trans 2367 C5-6 Clutch not calibrated
Trans 2368 Low Range Clutch not calibrated
Trans 2369 Mid Range Clutch not calibrated
Trans 2370 High Clutch not calibrated
Trans 2371 Reverse Clutch not calibrated
Trans 2372 Creep Clutch is not calibrated
Trans 2373 Master Clutch not calibrated
Trans 2800 Auto Guidance Isolation valve driver Fault
Trans 2805 System pressure valve solenoid circuit is open circuit or shorted to ground
Trans 2806 System pressure solenoid is shorted to B+
Trans 2807 Transmission output rpm over speed
Trans 2809 The battery voltage is too low to permit operation of the clutch solenoids.
Trans 2811 Transmission Oil Temperature Hot
Trans 2812 Transmission Oil Temperature sensor short to B+ or open circuit
Trans 2813 Transmission oil temperature Sensor Short to Ground
Trans 2814 Integrated Control Panel off line
Trans 2815 Governor Engine RPM alternator engine RPM mismatch
Trans 2816 Transmission regulated pressure accumulator is flat
Trans 2817 Governor is offline CAN bus
Trans 2818 Communication lost with the Armrest Control Module(ACM)
Trans 2819 Communication lost with the instrumentation controller.
Trans 2820 System pressure low possible System pressure hydraulic pump failure or leak
Trans 2821 System Pressure Low fault
Trans 2850 The Park Brake is stuck on by no electrical power supplied when commanded on
Trans 2851 The Park Brake Driver has detected an over current or an open circuit condition
Trans 2852 The Park Brake is stuck on by no electrical power supplied to the solenoid when driver is commanded on. Possible service brake bottom brake switches open.
Trans 2055 No signal from wheel speed sensor.
Trans 2873 Software is out of the calibration mode and the park brake request is still active. If this fault is detected there is a bug in the software
Trans 2874 The park brakes commanded on and gear is engaged and there is no park brake request from calibration. If this fault is detected there is a bug in the software
Trans 2900 Torque sensor Gap is on the larger end of the tolerance (CCH Only)
Trans 2901 Signal received from the torque sensor is not in any fault range or normal range tolerance (CCH Only)
Trans 2902 Torque sensor has declared an internal fault tolerance (CCH Only)
Trans 2903 Torque sensor supply voltage below 4.8 volts tolerance (CCH Only)
Trans 2910 12VF1voltage supply is low. (possible blown fuse*)
Trans 2911 12VT1voltage supply is low. (possible blown fuse*)
Trans 2912 12VF2voltage supply is low. (possible blown fuse*)
Trans 2913 12VHvoltage supply is low. (possible blown fuse*)
Trans 2914 12VF3voltage supply is low. (possible blown fuse*)
Trans 2915 12VS1voltage supply is low. (possible blown fuse*)
Engine 3000 Unknown ECM Error Code Received
Engine 3999 Unknown ECM Error Code Received
Engine 3001 Foot Throttle Sensor -Signal Not Plausible
Engine 3002 Foot Throttle Sensor -Signal Above Range Max.
Engine 3003 Foot Throttle Sensor -Signal Below Range Min.
Engine 3004 Foot Throttle Sensor -No Signal -Error
Engine 3006 Coolant Temperature Sensor -Signal Not Plausible(Compared with Engine Oil Temperature)
Engine 3007 Coolant Temperature Sensor -Signal Above Range Max.
Engine 3008 Coolant Temperature Sensor -Signal Below Range Min.
Engine 3009 Coolant Temperature Sensor -(via CAN) No Signal
Engine 3010 Air Intake Temperature Sensor -Signal Above Range Max.
Engine 3011 Air Intake Temperature Sensor -Signal Above Range Min.
Engine 3012 Air Intake Temperature Sensor -(via CAN) No Signal
Engine 3015 Fuel Temperature Signal -Signal Above Range Max.
Engine 3016 Fuel Temperature Signal -Signal Below Range Min.
Engine 3019 Boost Pressure Sensor -Signal Above Range Max.
Engine 3021 Boost Pressure Sensor -(via CAN) No Signal
Engine 3022 Boost Pressure Sensor -Signal Not Plausible
Engine 3023 Atmospheric Pressure Sensor -Signal Not Plausible Compared with Boost Pressure
Engine 3024 Atmospheric Pressure Sensor -Signal Above Range Max.
Engine 3025 Atmospheric Pressure Sensor -Signal Below Range Min.
Engine 3028 Oil Pressure Too Low
Engine 3029 Oil Pressure Sensor _Short circuit to Battery
Engine 3030 Oil Pressure Sensor _Short circuit to Ground
Engine 3031 Oil Pressure Sensor -Hardware Error
Engine 3032 Oil Pressure Sensor -Value Too High
Engine 3033 Oil Temperature Sensor -Signal Not Plausible (Compared with Coolant Temperature)
Engine 3034 Oil Temperature Sensor -Signal Above Range Max.
Engine 3035 Oil Temperature Sensor -Signal Below Range Min.
Engine 3036 Oil Temperature Sensor -(via CAN) No Signal
Engine 3037 Boost Pressure Sensor -Signal Low
Engine 3038 Constant Engine RPM Activate / Select Switch _Short circuit to Ground
Engine 3039 Cruise Control Actuating Device -Evaluation Error
Engine 3043 Vehicle Speed Sensing -Hardware Conversion Error
Engine 3044 Vehicle Speed Sensing -Signal Above Range Max.
Engine 3045 Vehicle Speed Sensing -Signal Below Range Min.
Engine 3046 Vehicle Speed Sensing -Signal Not Plausible
Engine 3047 Main Relay 2 Failure _Short circuit to Battery
Engine 3048 Main Relay 2 Failure _Short circuit to Ground
Engine 3051 Battery Voltage to ECM too High
Engine 3052 Battery Voltage to ECM too Low
Engine 3053 Vehicle Speed Sensing (Tacho) -PWM Frequency Too High
Engine 3054 Vehicle Speed Sensing (Tacho) -PWM Average Frequency Above Limit
Engine 3055 Vehicle Speed Sensing (Tacho) -PWM Average Frequency Below Limit
Engine 3056 Vehicle Speed Sensing (Tacho) -Not Plausible
Engine 3057 Timeout of CAN Message High Resolution Wheel Speed
Engine 3058 Timeout of CAN Message Vehicle Dynamics Control Unit
Engine 3059 ECM After run was Interrupted
Engine 3060 Cylinder1 -Unclassifiable Error in Injector
Engine 3061 Cylinder1 -Injector Cable Short circuit (Low Side to Battery)
Engine 3062 Cylinder1 -Application Dependent
Engine 3063 Cylinder1 -Injector Cable Short circuit (High Side to Ground)
Engine 3064 Cylinder5 -Unclassifiable Error in Injector
Engine 3065 Cylinder5 -Injector Cable Short circuit (Low Side to Battery)
Engine 3066 Cylinder5 -Application Dependent
Engine 3067 Cylinder5 -Injector Cable Short circuit (High Side to Ground)
Engine 3068 Cylinder3 -Unclassifiable Error in Injector
Engine 3069 Cylinder3 -Injector Cable Short circuit (Low Side to Battery)
Engine 3070 Cylinder3 -Application Dependent
Engine 3071 Cylinder3 -Injector Cable Short circuit (High Side to Ground)
Engine 3072 Cylinder6 -Unclassifiable Error in Injector
Engine 3073 Cylinder6 -Injector Cable Short circuit (Low Side to Battery)
Engine 3074 Cylinder6 -Application Dependent
Engine 3075 Cylinder6 -Injector Cable Short circuit (High Side to Ground)
Engine 3076 Cylinder2 -Unclassifiable Error in Injector
Engine 3077 Cylinder2 -Injector Cable Short circuit (Low Side to Battery)
Engine 3078 Cylinder2 -Application Dependent
Engine 3079 Cylinder2 -Injector Cable Short circuit (High Side to Ground)
Engine 3080 Cylinder4 -Unclassifiable Error in Injector
Engine 3081 Cylinder4 -Injector Cable Short circuit (Low Side to Battery)
Engine 3082 Cylinder4 -Application Dependent
Engine 3083 Cylinder4 -Injector Cable Short circuit (High Side to Ground)
Engine 3088 Crankshaft Sensor -No Signal
Engine 3089 Crankshaft Sensor -Invalid Signal
Engine 3090 Camshaft Sensor -No Signal
Engine 3091 Camshaft Sensor -Invalid Signal
Engine 3092 Offset Between Camshaft and Crankshaft -Not Plausible
Engine 3093 Offset Between Camshaft and Crankshaft -Outside Boundaries
Engine 3095 Operating with Camshaft Sensor Only -Backup Mode
Engine 3096 Tier 3: ECM Bus Off on CAN A Tier 4a: ECM Bus Off on Vehicle CAN
Engine 3097 ECM Bus Off on Engine private CAN
Engine 3098 Timeout of CAN Message TSC1-TE (When Active)
Engine 3099 Timeout of CAN Message TSC1-TE (When Inactive)
Engine 3100 Timeout of CAN Message TSC1-AE (When Active)
Engine 3101 Timeout of CAN Message TSC1-AE (When Inactive)
Engine 3102 Rail Pressure Sensor CP3 -Signal Below Range Min.
Engine 3104 Rail Pressure Relief Valve -Open
Engine 3105 Rail Pressure Relief Valve -Pressure Shock Requested
Engine 3106 Rail Pressure Relief Valve -Did Not Open After Pressure Shock
Engine 3107 Metering Unit _Short circuit to Battery
Engine 3108 Metering Unit _Short circuit to Ground
Engine 3110 Rail Pressure Sensor Offset Monitoring -Value above Limit
Engine 3111 Rail Pressure Sensor Offset Monitoring -Value below Limit
Engine 3112 Rail Pressure Sensor CP3 -Signal Above Range Max.
Engine 3113 Main Relay 1 (High Pressure Pump -power supply to the fuel metering unit) -Short to Battery
Engine 3114 Main Relay 1 (High Pressure Pump -power supply to the fuel metering unit) Short to Ground
Engine 3117 PTO Twist Sensor -Out of Range
Engine 3118 ECM 12V Sensor Supply Voltage High
Engine 3119 ECM 12V Sensor Supply Voltage Low
Engine 3120 PTO Twist Sensor -Not Plausible
Engine 3121 PTO Twist Sensor -Open Circuit
Engine 3122 PTO Twist Sensor _Short circuit to Ground
Engine 3123 PTO Twist Sensor -Not Calibrated
Engine 3124 Hand Throttle -Channel 2 Above Range Max.
Engine 3125 Hand Throttle -Channel 2 Below Range Min.
Engine 3126 Hand Throttle -Channel 1 Signal Above Range Max.
Engine 3127 Hand Throttle -Channel 1 Signal Below Range Min.
Engine 3128 Hand Throttle -Channel Difference Error
Engine 3129 Hand Throttle -Idle Switch Closed Circuit
Engine 3130 Hand Throttle -Idle Switch Open Circuit
Engine 3131 Grid Heater Always Switched On
Engine 3133 Cold Start Lamp -No Load
Engine 3134 Cold Start Lamp _Short circuit to Battery
Engine 3135 Cold Start Lamp _Short circuit to Ground
Engine 3136 Cold Start Lamp -Excessive Temperature
Engine 3137 Metering Unit -Open Load
Engine 3138 Metering Unit -Temperature Too High
Engine 3139 Metering Unit Signal Range Check -Signal Too High
Engine 3140 Metering Unit Signal Range Check -Signal Too Low
Engine 3141 Fuel Flow Set point Too Low
Engine 3142 High Pressure Test -Test Active
Engine 3143 Grid Heater Switch Off Test (Voltage Drop Too High)
Engine 3144 Grid Heater Switch Off Test (Voltage Drop Too Low)
Engine 3145 Terminal 15 -No Signal
Engine 3146 Water Detected In Fuel
Engine 3147 Oil Temperature Too High
Engine 3148 Coolant Temperature Sensor Dynamic Test -Failure (Minimum Temperature Raise Not Reached)
Engine 3149 Coolant Temperature Sensor Test -Failure (Minimum Temperature Not Reached)
Engine 3150 System/Amber Warning Lamp _Short circuit to Battery
Engine 3151 System/Amber Warning Lamp _Short circuit to Ground
Engine 3152 System/Amber Warning Lamp -No Load
Engine 3153 System/Amber Warning Lamp -Excessive Temperature
Engine 3154 Grid Heater Relay _Short circuit to Battery
Engine 3155 Grid Heater Relay _Short circuit to Ground
Engine 3156 Grid Heater Relay -No Load
Engine 3157 ECM Not Detected on CAN bus
Engine 3158 Invalid ECM Checksum
Engine 3159 Invalid Engine Reference Torque
Engine 3160 Fan Actuator _Short circuit to Battery
Engine 3161 Fan Actuator _Short circuit to Ground
Engine 3162 Fan Actuator -Open Load
Engine 3163 Fan Actuator -Temperature Too High
Engine 3164 Fan Speed Sensor _Signal High
Engine 3165 Fan Speed Sensor -Signal Low
Engine 3166 Fuel Filter Heater Relay _Short circuit to Battery
Engine 3167 Fuel Filter Heater Relay _Short circuit to Ground
Engine 3168 Fuel Filter Heater Relay -Open Load
Engine 3169 Fuel Filter Heater Relay -Signal Not Plausible
Engine 3176 Set point of Metering Unit Not Plausible in Overrun
Engine 3177 Engine Over speed Detected
Engine 3178 Timeout of CAN Message BC2EDC1
Engine 3179 Timeout of CAN Message BC2EDC2
Engine 3180 Timeout of CAN Message VCM2EDC
Engine 3181 Rail Pressure Positive Deviation Too High Concerning Set point
Engine 3182 Timeout of CAN Message RxCCVS
Engine 3183 Timeout of CAN Message TSC1-VR (When Active)
Engine 3184 Timeout of CAN Message TSC1-VR (When Inactive)
Engine 3185 Timeout of CAN message TF
Engine 3186 Cylinder1 Warning -Fast Decay Error
Engine 3187 Cylinder1 Warning -Application Dependent
Engine 3188 Cylinder1 Warning -Injector Circuit Low
Engine 3189 Cylinder1 Warning -Current Level Error
Engine 3190 Cylinder2 Warning -Fast Decay Error
Engine 3191 Cylinder2Warning -Application Dependent
Engine 3192 Cylinder2 Warning -Open Load
Engine 3193 Cylinder2 Warning -Current Level Error
Engine 3194 Cylinder3 Warning -Fast Decay Error
Engine 3195 Cylinder3 Warning -Application Dependent
Engine 3196 Cylinder3 Warning -Open Load
Engine 3197 Cylinder3 Warning -Current Level Error
Engine 3198 Cylinder4 Warning -Fast Decay Error
Engine 3199 Cylinder4 Warning -Application Dependent
Engine 3200 Cylinder4 Warning -Open Load
Engine 3201 Cylinder4 Warning -Current Level Error
Engine 3202 Cylinder5 Warning -Fast Decay Error
Engine 3203 Cylinder5 Warning -Application Dependent
Engine 3204 Cylinder5 Warning -Open Load
Engine 3205 Cylinder5 Warning -Current Level Error
Engine 3206 Cylinder6 Warning -Fast Decay Error
Engine 3207 Cylinder6 Warning -Application Dependent
Engine 3208 Cylinder6 Warning -Open Load
Engine 3209 Cylinder6 Warning -Current Level Error
Engine 3210 Bank1 -General Short circuit on Injection Cable
Engine 3211 Bank1 -Injection Cable Short circuit Low Side to Ground
Engine 3212 Bank1 -Application Dependent
Engine 3213 Bank1 -Unclassifiable Error
Engine 3214 Bank1 Warning -Application Dependent
Engine 3215 Bank1 Warning -Application Dependent
Engine 3216 Bank1 Warning -Open Load
Engine 3217 Bank1 Warning -Unclassifiable Error
Engine 3218 Bank2-General Short circuit on Injection Cable
Engine 3219 Bank2 -Injection Cable Short circuit Low Side to Ground
Engine 3220 Bank2 -Application Dependent
Engine 3221 Bank2 -Unclassifiable Error
Engine 3222 Bank2 Warning -Application Dependent
Engine 3223 Bank2 Warning -Application Dependent
Engine 3224 Bank2 Warning -Open Load
Engine 3225 Bank2 Warning -Unclassifiable Error
Engine 3226 Messages SRA2EDC
Engine 3227 Injection Processor (CY33X) Error -Internal Reset / Clock Loss / Voltage Too Low
Engine 3228 Injection Processor (CY33X) Error -Unlocked / Initialization Failure
Engine 3229 Injection Processor (CY33X) Error -Injections Limited By Software
Engine 3230 Injection Processor (CY33X) Error -SPI Communication Failure
Engine 3231 Injection Processor Error -Internal Reset / Clock Loss / Voltage Too Low
Engine 3232 Injection Processor Error -Unlocked / Initialization Failure
Engine 3233 Injection Processor Error -Test Mode
Engine 3234 Injection Processor Error -SPI Communication Failure
Engine 3235 Number of Injections Limited -by Charge Balance
Engine 3236 Number of Injections Limited -by Quantity Balance
Engine 3237 Number of Injections Limited -by Software
Engine 3238 ECM Internal SPI Communication Error -CJ940
Engine 3239 ECM EEPROM -Read Operation Failure
Engine 3240 ECM EEPROM -Write Operation Failure
Engine 3241 ECM EEPROM -Default Value Used
Engine 3242 ECM (Locked) Recovery Occurred
Engine 3243 ECM (Suppressed) -Recovery Occurred
Engine 3244 ECU Recovery (Visible) -Recovery Occurred
Engine 3245 ECM Processor -Watchdog Not Plausible
Engine 3246 Shutoff Paths During Initialization -Watchdog
Engine 3247 Shutoff Paths During Initialization -Supply Voltage Too High
Engine 3248 Shutoff Paths During Initialization -Supply Voltage Too Low
Engine 3249 TPU Monitoring -Time Deviation between TPU and System Not Plausible
Engine 3250 Dataset -Variant Defect
Engine 3251 Dataset -Requested Variant Could Not Be Set
Engine 3252 Controller Watchdog -SPI Communication Failure
Engine 3253 ADC Monitoring -Reference Voltage Too High
Engine 3254 ADC Monitoring -Reference Voltage Too Low
Engine 3255 ADC Monitoring -Test Impulse Error
Engine 3256 ADC Monitoring -Queue Error
Engine 3257 Turbine Speed and Air Pressure Too High
Engine 3258 High Side Power -Short circuit to Battery
Engine 3259 High Side Power _Short circuit to Ground
Engine 3260 Low Side Power -Open Load
Engine 3261 Low Side Power -Short circuit to Battery of Excess Temperature
Engine 3262 Low Side Power _Short circuit to Ground
Engine 3263 ECM Bus Off on CAN C
Engine 3264 Immobilizer -Injection Disabled
Engine 3265 Overrun Monitoring -Injection Time Too Long
Engine 3266 Redundant Engine Speed in Overrun Monitoring -Speed Signal Not Plausible
Engine 3267 Main relay 3 _Short circuit to Battery
Engine 3268 Main relay 3 _Short circuit to Ground
Engine 3269 Grid Heater Switch On Test -Voltage Drop Too High
Engine 3270 Grid Heater Switch On Test -Voltage Drop Too Low
Engine 3271 Fuel Low Pressure Sensor -(via CAN) No Signal
Engine 3272 Fuel Low Pressure Sensor -Signal Above Range Max.
Engine 3273 Fuel Low Pressure Sensor -Signal Below Range Min.
Engine 3274 Fuel Low Pressure Sensor Dynamic Plausibility Test -Above Map
Engine 3275 Fuel Low Pressure Sensor Dynamic Plausibility Test -Below Map
Engine 3276 MIL Visualization Not Available for BC2EDC1
Engine 3277 Timeout of CAN Message Dashboard Display
Engine 3278 ECM Internal Supply Voltage Too High -CJ940 Above Limit
Engine 3279 ECM Internal Supply Voltage Too Low -CJ940 Below Limit
Engine 3280 Sensor Supply Voltage 1 -High
Engine 3281 Sensor Supply Voltage 1 - Low
Engine 3282 Timeout of CAN Message WSI (Wheel Speed Info)
Engine 3283 Sensor Supply Voltage 2 -High
Engine 3284 Sensor Supply Voltage 2 - Low
Engine 3285 Sensor Supply Voltage 3 -High
Engine 3286 Sensor Supply Voltage 3 - Low
Engine 3287 Turbo Compound Monitoring -No Signal
Engine 3288 Turbo Compound Monitoring -Signal High
Engine 3289 Turbo Compound Monitoring -Signal Low
Engine 3290 Turbo Compound Monitoring -Signal Not Plausible
Engine 3291 Cylinder 1 Specific Errors -No Signal
Engine 3292 Cylinder 1 Specific Errors -Signal Low
Engine 3293 Cylinder 1 BIP Search Failure -Too Many Unsuccessful Searched
Engine 3294 Cylinder 1 Specific Errors -Signal Not Plausible
Engine 3295 Cylinder 2 Specific Errors -No Signal
Engine 3296 Cylinder 2 Specific Errors -Signal Low
Engine 3298 Cylinder 2 Specific Errors -Signal Not Plausible
Engine 3299 Cylinder 3 Specific Errors -No Signal
Engine 3300 Cylinder 3 Specific Errors -Signal Low
No comments:
Post a Comment